CalAmp GUARDIAN User Manual Page 80
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
• Power input: 10-30 VDC at 60 watts maximum.
- Interface connection
o Guardian uses an 8-pin User Port interface connector.
• Connector is included with the Guardian.
• Connector CalAmp PN 415-1001-208.
• Wire connections can be opened with insertion tool PN 350-5006-001 or a small screwdriver.
The DL-3282 Modem uses the following connections
- User Interface
o 10-pin 3M ribbon-style connector.
o 25-pin DB-25 female RS-232 serial data connector.
o DE-15 high density serial connector — special purpose connection.
- Power connection
o Power is applied to the DL-3282 through the 10-pin ribbon-cable connection.
o Power input: 7-16 VDC at 50 mA (Max.)
o Use cable CalAmp PN 023-3410-109 for power and interface to the Guardian.
PROGRAMMING AND SETUP
Use the Guardian FPS (Field Programming Software) to program the Guardian. Guardian FPS is available on the CalAmp
website
http://www.calamp.com/support.
When the Guardian is being interfaced with an existing DL-3400 or DL-3282 radio modem system, the Guardian must
be programmed to match the settings of the DL-3400 analog radios. Information for programming a Guardian into a
DL-3400 system is provided in the previous Appendix, Appendix B — Guardian and DL-3400 Interoperability. Detailed
information for programming the Guardian is also provided in Chapter 5 Guardian Field Programming Software in this
User Manual.
The following programming steps will provide much of the information required to operate the Guardian in an analog
data system.
Set Guardian Parameters
Once the parameters for the existing DL-3400 have been logged, connect the Guardian to the proper power supply
voltage (10-30 VDC 60 watt maximum at 10 watt RF power). Connect the DE-9 to DE-9 data cable (CalAmp PN 697-
4008-408 or equivalent) to the Guardian Setup port.
Note: The Guardian FPS is set for COM1 by default. Change this if necessary.
- Programming parameters are 57,600, 8, N, 1, DTR, None.
- Handshaking should be set to Buffered with no HS.
With the Guardian connected to proper power source, antenna terminated, and programming cable connected to the
Setup port of the Guardian, click Config (at the upper left corner of the programming window) to access the Guardian
Configuration window.
Figure 49 Config button
Guardian™ Serial Modem or Analog Radio for Licensed Spectrum PN 001-5006-000 Rev. 3 | Page 72
- Guardian 1
- REVISION HISTORY 3
- Important Notice 4
- Copyright Notice 4
- Regulation Certifications 5
- Certifications 5
- 1 GUARDIAN OVERVIEW 9
- 1.1 GENERAL DESCRIPTION 9
- 1.3 LINK CONFIGURATIONS 10
- 1.4 PHYSICAL DESCRIPTION 11
- 1.4.1 FRONT PANEL 11
- 1.4.2 LED PANEL 11
- 1.4.3 USER INTERFACE PORT 12
- 1.4.4 SETUP AND COM PORTS 13
- 1.4.5 POWER CONNECTOR 14
- 1.4.6 ANTENNA CONNECTOR 14
- 1.4.7 CHASSIS DIMENSIONS 15
- 1.5.1 GUARDIAN RADIO 15
- Table 7 Guardian Demo Kits 16
- Table 8 Guardian Power Cable 16
- Table 9 Guardian Fan Kits 16
- 2.1 SINGLE COVERAGE AREA 17
- 2.2 NETWORK ARCHITECTURE 17
- 2.2.1 POINT-TO-POINT 17
- 2.2.2 POINT-TO-MULTIPOINT 18
- 2.2.4 PEER-TO-PEER 18
- 2.2.5 STORE AND FORWARD 18
- 2.4.1 SITE SELECTION 19
- 2.4.2 SITE SURVEY 20
- 2.5.2 ANTENNA OVERVIEW 20
- 2.5.3 THE WRONG COMBINATION 20
- 2.5.4 GOOD DESIGN PRACTICES 22
- 2.6.1 ANTENNA GAIN 22
- Table 11 Antenna Types 23
- 2.8 RADIO INTERFERENCE 25
- 3 SETUP AND CONFIGURATION 26
- 3.1 INSTALL THE ANTENNA 26
- 4 UNIT STATUS 28
- 4.1.1 LONG ID NUMBER 28
- 4.1.2 SHORT ID 28
- 4.2 DIAGNOSTICS 28
- 4.2.1 ONLINE DIAGNOSTICS 29
- 4.2.2 OFFLINE DIAGNOSTICS 29
- 4.2.3 REMOTE COMMANDS 29
- 5.1 INTRODUCTION 30
- 5.3 PORT SETTINGS 31
- Table 15 Communication Modes 32
- 5.4 PORT STATISTICS 33
- 5.6.1 MODEM SETTINGS 38
- 5.6.2 RF LINK 39
- 5.6.3 COM PORT 40
- 5.9.1 RF LINK 46
- 5.9.2 LOADER SETTINGS 47
- 5.11 VERSION REQUEST 49
- 5.14 OFFLINE LINK TEST 52
- 5.15 OFFLINE DIAGNOSTICS 53
- 5.16 ONLINE DIAGNOSTICS 55
- Figure 32 Online Diagnostics 56
- 5.17 PACKET TEST 57
- 5.18 ARRAY TEST 59
- 5.19 ASCII / HEX TERMINAL 61
- 5.19.1 ASCII TERMINAL 61
- 5.19.2 HEX TERMINAL 61
- 5.21 END TO END TEST 63
- 6 GUARDIAN SPECIFICATIONS 65
- APPLICABLE PRODUCTS 69
- APPLICATION 69
- HARDWARE 69
- PROGRAMMING AND SETUP 70
- SET GUARDIAN PARAMETERS 72
- LINK CONFIGURATION 74
- Pin 4 is 75
- CD or RSSI 75
- PROGRAMMING 76
- Click Write Guardian to 77
- INSTALLATION 78
- 10-pin user 86
- PN 023-3410-109 86
- Interface cable 86
- Note frequencies 92
- Note power 92
- WARRANTY STATEMENT 99
Related products and manuals for Networking CalAmp GUARDIAN
Networking CalAmp Fusion Specifications
(2 pages)
(2 pages)
Networking CalAmp HiPR-900 User Manual
(105 pages)
(105 pages)
Networking CalAmp GEMINI G3 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 1.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals