CalAmp GUARDIAN User Manual Page 28
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4 UNIT STATUS
In addition to unit status information provided by the five tricolor LEDs in the LED Panel, unit status information is also
displayed in the Diagnostics pane of the User Configuration window (page 26 for Modem mode or page 35 for Loader
Mode) of the Guardian Field Programming Software, and is explained in Chapter 5.
4.1 UNIT IDENTIFICATION AND STATUS
Each Guardian has addressing capability which is used for diagnostics and remote commands only.
The Long ID and Short ID with which each Guardian is configured are displayed directly under the Firmware version
number in the main window of the Guardian Field Programming Software.
Figure 11 Unit Status Information
If this area displays blank (for example when software is first started or initial connection has not been established),
click Version, immediately to the left and the FPS reads this information from the Guardian and it is displayed.
4.1.1 LONG ID NUMBER
This value is assigned at the factory but may be modified using the Field Programming Software. The ID Number is used
to uniquely identify the Guardian for remote commands and Offline Diagnostics. The ID Number may have values
within the range of 1 to 4294967295 but multiples of 1024 should not be used.
4.1.2 SHORT ID
This value (maximum 1023) is the low order 10 bits of the ID Number. It is used to identify online diagnostics only. It
may not be modified directly using the Field Programming Software; it is always derived from the ID Number. All units
within a network should have unique Short ID numbers to avoid ambiguity in Online Diagnostics reports.
The Guardian Field Programming Software may be used to check the value of the Short ID. When setting up a network,
we recommend checking each unit to make sure there is no duplication of Short ID numbers. Duplications may be
resolved by changing the Long ID Number.
If ID Numbers are set within the range of 1 to 1023, the ID Number and the Short ID will always have the same value.
4.2 DIAGNOSTICS
Guardian units continually monitor and report on their environmental and operating conditions.
Guardian™ Serial Modem or Analog Radio for Licensed Spectrum PN 001-5006-000 Rev. 3 | Page 20
- Guardian 1
- REVISION HISTORY 3
- Important Notice 4
- Copyright Notice 4
- Regulation Certifications 5
- Certifications 5
- 1 GUARDIAN OVERVIEW 9
- 1.1 GENERAL DESCRIPTION 9
- 1.3 LINK CONFIGURATIONS 10
- 1.4 PHYSICAL DESCRIPTION 11
- 1.4.1 FRONT PANEL 11
- 1.4.2 LED PANEL 11
- 1.4.3 USER INTERFACE PORT 12
- 1.4.4 SETUP AND COM PORTS 13
- 1.4.5 POWER CONNECTOR 14
- 1.4.6 ANTENNA CONNECTOR 14
- 1.4.7 CHASSIS DIMENSIONS 15
- 1.5.1 GUARDIAN RADIO 15
- Table 7 Guardian Demo Kits 16
- Table 8 Guardian Power Cable 16
- Table 9 Guardian Fan Kits 16
- 2.1 SINGLE COVERAGE AREA 17
- 2.2 NETWORK ARCHITECTURE 17
- 2.2.1 POINT-TO-POINT 17
- 2.2.2 POINT-TO-MULTIPOINT 18
- 2.2.4 PEER-TO-PEER 18
- 2.2.5 STORE AND FORWARD 18
- 2.4.1 SITE SELECTION 19
- 2.4.2 SITE SURVEY 20
- 2.5.2 ANTENNA OVERVIEW 20
- 2.5.3 THE WRONG COMBINATION 20
- 2.5.4 GOOD DESIGN PRACTICES 22
- 2.6.1 ANTENNA GAIN 22
- Table 11 Antenna Types 23
- 2.8 RADIO INTERFERENCE 25
- 3 SETUP AND CONFIGURATION 26
- 3.1 INSTALL THE ANTENNA 26
- 4 UNIT STATUS 28
- 4.1.1 LONG ID NUMBER 28
- 4.1.2 SHORT ID 28
- 4.2 DIAGNOSTICS 28
- 4.2.1 ONLINE DIAGNOSTICS 29
- 4.2.2 OFFLINE DIAGNOSTICS 29
- 4.2.3 REMOTE COMMANDS 29
- 5.1 INTRODUCTION 30
- 5.3 PORT SETTINGS 31
- Table 15 Communication Modes 32
- 5.4 PORT STATISTICS 33
- 5.6.1 MODEM SETTINGS 38
- 5.6.2 RF LINK 39
- 5.6.3 COM PORT 40
- 5.9.1 RF LINK 46
- 5.9.2 LOADER SETTINGS 47
- 5.11 VERSION REQUEST 49
- 5.14 OFFLINE LINK TEST 52
- 5.15 OFFLINE DIAGNOSTICS 53
- 5.16 ONLINE DIAGNOSTICS 55
- Figure 32 Online Diagnostics 56
- 5.17 PACKET TEST 57
- 5.18 ARRAY TEST 59
- 5.19 ASCII / HEX TERMINAL 61
- 5.19.1 ASCII TERMINAL 61
- 5.19.2 HEX TERMINAL 61
- 5.21 END TO END TEST 63
- 6 GUARDIAN SPECIFICATIONS 65
- APPLICABLE PRODUCTS 69
- APPLICATION 69
- HARDWARE 69
- PROGRAMMING AND SETUP 70
- SET GUARDIAN PARAMETERS 72
- LINK CONFIGURATION 74
- Pin 4 is 75
- CD or RSSI 75
- PROGRAMMING 76
- Click Write Guardian to 77
- INSTALLATION 78
- 10-pin user 86
- PN 023-3410-109 86
- Interface cable 86
- Note frequencies 92
- Note power 92
- WARRANTY STATEMENT 99
Related products and manuals for Networking CalAmp GUARDIAN
Networking CalAmp Fusion Specifications
(2 pages)
(2 pages)
Networking CalAmp HiPR-900 User Manual
(105 pages)
(105 pages)
Networking CalAmp GEMINI G3 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.142 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals