CalAmp GUARDIAN User Manual Page 32
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
COM Port
Selects COM Port number (1- 32) for Primary and Secondary COM Ports. Default is COM1.
Baud Rate
Selects the communication speed for Primary and Secondary COM Ports. Default is 57600 bps.
Data Bits
Selects number of data bits (7 or 8) transmitted or received for the Primary and Secondary COM Ports. Default is 8.
Parity
Selects transmission or reception of any Parity bits for the Primary and Secondary COM Ports. Default is None.
Stop Bits
Selects number of Stop Bits (1 or 2) transmitted or received for the Primary and Secondary COM Ports. Default is 1.
DTR Enable
Used to assert DTR (Data Terminal Ready) line of the RS-232 Port when the port is open for the Primary and Secondary
COM Ports. Default is NO.
Swap COM Ports
Clicking the Swap Com Ports button moves the Secondary COM Port settings to the Primary COM Port (and moves the
Primary COM Port to the Secondary settings). Since Guardian programming is done through the Primary COM Port, this
is useful when two units are connected to the Primary and Secondary COM Ports. A Swap COM Ports allows the second
unit to be programmed without switching programming cables.
5.3.1 PRIMARY AND SECONDARY PORT SETTINGS COMMUNICATIONS MODES
The Mode menu located near the bottom of the Port Settings window (see Figure 14) configures the communications
mode for the Primary and Secondary PC Port. See the following table for Communication Mode configurations.
Table 15 Communication Modes
Mode
Description
Sync/ESC with No HS
Sends data using Sync/byte-stuffing protocol without handshaking.
Buffered with No HS
Sends buffered data without handshaking (this mode required for DOX
operation.) This is the Default.
Sync/Esc with RTS/CTS HS
Sends data using the Sync/Esc byte-stuffing protocol with RTS/CTS
hardware handshaking.
Buffered with RTS/CTS HS
Sends buffered data with RTS/CTS hardware handshaking.
Sync/Esc with Flow Control HS
Sends data using the Sync/Esc byte-stuffing protocol with flow control
handshaking.
Buffered with Flow Control HS
Sends buffered data with flow control hardware handshaking.
Guardian™ Serial Modem or Analog Radio for Licensed Spectrum PN 001-5006-000 Rev. 3 | Page 24
- Guardian 1
- REVISION HISTORY 3
- Important Notice 4
- Copyright Notice 4
- Regulation Certifications 5
- Certifications 5
- 1 GUARDIAN OVERVIEW 9
- 1.1 GENERAL DESCRIPTION 9
- 1.3 LINK CONFIGURATIONS 10
- 1.4 PHYSICAL DESCRIPTION 11
- 1.4.1 FRONT PANEL 11
- 1.4.2 LED PANEL 11
- 1.4.3 USER INTERFACE PORT 12
- 1.4.4 SETUP AND COM PORTS 13
- 1.4.5 POWER CONNECTOR 14
- 1.4.6 ANTENNA CONNECTOR 14
- 1.4.7 CHASSIS DIMENSIONS 15
- 1.5.1 GUARDIAN RADIO 15
- Table 7 Guardian Demo Kits 16
- Table 8 Guardian Power Cable 16
- Table 9 Guardian Fan Kits 16
- 2.1 SINGLE COVERAGE AREA 17
- 2.2 NETWORK ARCHITECTURE 17
- 2.2.1 POINT-TO-POINT 17
- 2.2.2 POINT-TO-MULTIPOINT 18
- 2.2.4 PEER-TO-PEER 18
- 2.2.5 STORE AND FORWARD 18
- 2.4.1 SITE SELECTION 19
- 2.4.2 SITE SURVEY 20
- 2.5.2 ANTENNA OVERVIEW 20
- 2.5.3 THE WRONG COMBINATION 20
- 2.5.4 GOOD DESIGN PRACTICES 22
- 2.6.1 ANTENNA GAIN 22
- Table 11 Antenna Types 23
- 2.8 RADIO INTERFERENCE 25
- 3 SETUP AND CONFIGURATION 26
- 3.1 INSTALL THE ANTENNA 26
- 4 UNIT STATUS 28
- 4.1.1 LONG ID NUMBER 28
- 4.1.2 SHORT ID 28
- 4.2 DIAGNOSTICS 28
- 4.2.1 ONLINE DIAGNOSTICS 29
- 4.2.2 OFFLINE DIAGNOSTICS 29
- 4.2.3 REMOTE COMMANDS 29
- 5.1 INTRODUCTION 30
- 5.3 PORT SETTINGS 31
- Table 15 Communication Modes 32
- 5.4 PORT STATISTICS 33
- 5.6.1 MODEM SETTINGS 38
- 5.6.2 RF LINK 39
- 5.6.3 COM PORT 40
- 5.9.1 RF LINK 46
- 5.9.2 LOADER SETTINGS 47
- 5.11 VERSION REQUEST 49
- 5.14 OFFLINE LINK TEST 52
- 5.15 OFFLINE DIAGNOSTICS 53
- 5.16 ONLINE DIAGNOSTICS 55
- Figure 32 Online Diagnostics 56
- 5.17 PACKET TEST 57
- 5.18 ARRAY TEST 59
- 5.19 ASCII / HEX TERMINAL 61
- 5.19.1 ASCII TERMINAL 61
- 5.19.2 HEX TERMINAL 61
- 5.21 END TO END TEST 63
- 6 GUARDIAN SPECIFICATIONS 65
- APPLICABLE PRODUCTS 69
- APPLICATION 69
- HARDWARE 69
- PROGRAMMING AND SETUP 70
- SET GUARDIAN PARAMETERS 72
- LINK CONFIGURATION 74
- Pin 4 is 75
- CD or RSSI 75
- PROGRAMMING 76
- Click Write Guardian to 77
- INSTALLATION 78
- 10-pin user 86
- PN 023-3410-109 86
- Interface cable 86
- Note frequencies 92
- Note power 92
- WARRANTY STATEMENT 99
Related products and manuals for Networking CalAmp GUARDIAN
Networking CalAmp Fusion Specifications
(2 pages)
(2 pages)
Networking CalAmp HiPR-900 User Manual
(105 pages)
(105 pages)
Networking CalAmp GEMINI G3 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.646 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals