CalAmp GUARDIAN User Manual Page 63
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3. Click OK to start the programming process. A file transfer progress window will be displayed and a message will be
displayed when the firmware file has been successfully programmed into the Guardian. The Guardian will reset
automatically and begin running the programmed firmware.
5.21 END TO END TEST
The Field Programming Software has several useful utilities embedded in the program that assist in testing the wireless
modems. The testing setup requires a computer running the Field Programming Software attached to each user COM
port on the Guardian wireless modems. The Utilities will allow the user to send ASCII text or Hex characters through
the Guardians being tested.
The Guardian modems must be set up so that they have the appropriate receive and transmit signal levels for the test.
The signal strength will be much stronger if the units are tested on the bench compared to being tested in a field
installation. These signals must be attenuated or the output power level adjusted if the units are being tested on the
bench.
ASCII Terminal
Under the Utilities menu choose the ASCII Terminal. From the ASCII Terminal window, choose the Primary selection.
This will open an ASCII terminal window using the primary COM port of the computer. This procedure should be
performed for both Guardian modems.
The ASCII Terminal utility has provisions for transmitting the ASCII data, displaying received ASCII data and displaying
ASCII transmitted data. Figure 36 shows the window for the Primary and Secondary ASCII Terminals.
Figure 36 End-to-End Test using ASCII Terminal
The above figure also shows the area that is used to send an ASCII text message. The ASCII data message is typed into
this area. The ASCII text message is then sent out the first Guardian through the computer’s primary port once the
Send button is clicked. The sent ASCII message is then displayed in the Tx Data area of the ASCII Terminal window. The
ASCII message is transmitted to the other Guardian. The ASCII terminal program will display the received ASCII message
in the Rx Data area.
Guardian™ Serial Modem or Analog Radio for Licensed Spectrum PN 001-5006-000 Rev. 3 | Page 55
- Guardian 1
- REVISION HISTORY 3
- Important Notice 4
- Copyright Notice 4
- Regulation Certifications 5
- Certifications 5
- 1 GUARDIAN OVERVIEW 9
- 1.1 GENERAL DESCRIPTION 9
- 1.3 LINK CONFIGURATIONS 10
- 1.4 PHYSICAL DESCRIPTION 11
- 1.4.1 FRONT PANEL 11
- 1.4.2 LED PANEL 11
- 1.4.3 USER INTERFACE PORT 12
- 1.4.4 SETUP AND COM PORTS 13
- 1.4.5 POWER CONNECTOR 14
- 1.4.6 ANTENNA CONNECTOR 14
- 1.4.7 CHASSIS DIMENSIONS 15
- 1.5.1 GUARDIAN RADIO 15
- Table 7 Guardian Demo Kits 16
- Table 8 Guardian Power Cable 16
- Table 9 Guardian Fan Kits 16
- 2.1 SINGLE COVERAGE AREA 17
- 2.2 NETWORK ARCHITECTURE 17
- 2.2.1 POINT-TO-POINT 17
- 2.2.2 POINT-TO-MULTIPOINT 18
- 2.2.4 PEER-TO-PEER 18
- 2.2.5 STORE AND FORWARD 18
- 2.4.1 SITE SELECTION 19
- 2.4.2 SITE SURVEY 20
- 2.5.2 ANTENNA OVERVIEW 20
- 2.5.3 THE WRONG COMBINATION 20
- 2.5.4 GOOD DESIGN PRACTICES 22
- 2.6.1 ANTENNA GAIN 22
- Table 11 Antenna Types 23
- 2.8 RADIO INTERFERENCE 25
- 3 SETUP AND CONFIGURATION 26
- 3.1 INSTALL THE ANTENNA 26
- 4 UNIT STATUS 28
- 4.1.1 LONG ID NUMBER 28
- 4.1.2 SHORT ID 28
- 4.2 DIAGNOSTICS 28
- 4.2.1 ONLINE DIAGNOSTICS 29
- 4.2.2 OFFLINE DIAGNOSTICS 29
- 4.2.3 REMOTE COMMANDS 29
- 5.1 INTRODUCTION 30
- 5.3 PORT SETTINGS 31
- Table 15 Communication Modes 32
- 5.4 PORT STATISTICS 33
- 5.6.1 MODEM SETTINGS 38
- 5.6.2 RF LINK 39
- 5.6.3 COM PORT 40
- 5.9.1 RF LINK 46
- 5.9.2 LOADER SETTINGS 47
- 5.11 VERSION REQUEST 49
- 5.14 OFFLINE LINK TEST 52
- 5.15 OFFLINE DIAGNOSTICS 53
- 5.16 ONLINE DIAGNOSTICS 55
- Figure 32 Online Diagnostics 56
- 5.17 PACKET TEST 57
- 5.18 ARRAY TEST 59
- 5.19 ASCII / HEX TERMINAL 61
- 5.19.1 ASCII TERMINAL 61
- 5.19.2 HEX TERMINAL 61
- 5.21 END TO END TEST 63
- 6 GUARDIAN SPECIFICATIONS 65
- APPLICABLE PRODUCTS 69
- APPLICATION 69
- HARDWARE 69
- PROGRAMMING AND SETUP 70
- SET GUARDIAN PARAMETERS 72
- LINK CONFIGURATION 74
- Pin 4 is 75
- CD or RSSI 75
- PROGRAMMING 76
- Click Write Guardian to 77
- INSTALLATION 78
- 10-pin user 86
- PN 023-3410-109 86
- Interface cable 86
- Note frequencies 92
- Note power 92
- WARRANTY STATEMENT 99
Related products and manuals for Networking CalAmp GUARDIAN
Networking CalAmp Fusion Specifications
(2 pages)
(2 pages)
Networking CalAmp HiPR-900 User Manual
(105 pages)
(105 pages)
Networking CalAmp GEMINI G3 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.175 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals